MICROBOT MOTOR DRIVER DOWNLOAD

Its use is very simple and you do not have to do anything, the type of input used is detected automatically when the board is powered. It has direction leds for help testing operations. By using our services, you agree to our use of cookies. On this shield the selection of the power source for motor outputs is accomplished by a jumper. All orders after this time will be shipped again from We would like to ask you to consider this in your order planning! It is based on the famous integrated circuit L, producted by STMicroelectronics; the L is an integrated monolithic circuit in a PowerSO20 package.

Uploader: Tautaur
Date Added: 15 October 2005
File Size: 7.95 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 99490
Price: Free* [*Free Regsitration Required]

The sensor is the integrated circuit TCN75A and you can refer to its datasheet to better understanding its communication protocol.

Add to shopping cart. The maximum supply voltage supported by this board is 30V. All orders after this time will be shipped again from The possibility of using two limit microswitches that will act as a protection, interrupting the movement of the motor in the two possible directions when the pressure of the microswitch is mltor, completes the functions on the board.

It has direction leds for help testing jotor. For the I2C communication, there are two different slave addresses selectable through moror jumper, and in this way it is possible to use two Easy Motor Controllers on the same serial line, and then control them by using a single external controller. Do you need an offer? The Easy Motlr Controller allows to control the speed and the direction of rotation of a DC motor through three different possible inputs: Add to project More from Microbot.

New Drivers  DWL-G650 XP DRIVER DOWNLOAD

To optimize the response to RC commands you also have the calibration function on the receiver signals. Moving the jumper from one side to the other the power source can be changed.

This shield is based on the L, a high voltage, high current dual full-bridge driver. The Easy Motor Controller provides two separate power supplies, one for the motor and the other one for the logic part; the latter can be pulled out through a jumper directly from that of the motor or alternatively from the BEC circuit of the RC receiver. To enable or disable each channel independently of the input signals there are provided two enable inputs E1, E2 positioned on the front of the board; motor velocity regulation is obtained applying to these pins a PWM signal with a 20KHz max.

It is a high voltage, high current dual fullbridge driver designed to accept standard Microboot logic levels and drive microbog loads such as relays,solenoids, DC and stepping motors.

DC Dual Motor Driver 30V 4A V2

Specifications Supply voltage 7 – 30V Supply current logic 24mA typ. To avoid dangerous overheating condition you can use the integrated I2C digital temperature sensor mounted close to the L chip. In fact when the L chip works at high current values it may become very hot and this heat can flow through all the shield.

This board also provides direction LED indicators for both channels; this is very usefull during setup stage to verify the firmware behaviour also without appling a real motor to the output. The Driver IC may become very hot when working with current more than 1A.

New Drivers  GBT AWRDACPI SOUND DRIVER

Make Dumb Devices Smart

To ensure safely operating condition you can measure the motor current absorption of each motor; this allow to avoid stall conditions. We will send you a mail when the product becomes available again Error during request registration Not available.

Its use is very simple and you do not have to do anything, the type of input used is detected automatically when the board is powered.

We would like to ask you to consider this in your order planning! View additional product data.

Microbot | Active Robots

Do you need a written offer before ordering? By using our services, you agree to our use of cookies. To prevent board damages, all driver lines are diode protected from back EMF.

The minimum supply voltage allowed is 7V, so you can use also two-cell LiPo batteries 7. Cookies help us deliver our services. By motlr our services, you agree to our use of cookies.

The Dual DC Motor Shield is a shield that has been projected to enable an Arduino board to drive two brushed DC motors or one 4-wire two-phase stepper moyor, controlling the speed and direction of each one independently. Supply voltage for motors 46Vmax. The maximum supply voltage supported by this board is 46V To ensure safely operating condition you can measure the motor current absorption of each motor; this allow to avoid stall conditions.